For the complex traditional stage lighting system, due to the lighting of the characters and the stage set and the different required lighting patterns, the debugging of this aspect includes the color tone, color, color temperature, brightness, projection range, scene of the dimming station, sequence. The editing of the program and many other aspects are not simple debugging of general practical engineering. Just like the sound system, it also needs a lot of serious debugging to complete, or as mentioned above, for the traditional complex lighting system. Design, construction and commissioning are best carried out with the help of professional design institutes and professional performance units.
In the lighting system debugging of general sound engineering, because there is no strict performance venue for the performance requirements, there are not many technical indicators involved in debugging. Relatively speaking, the debugging of the lighting system is not complicated, but there are also technical requirements higher than There are not many technical indicators for traditional stage lighting. Relatively speaking, the debugging of lighting systems is not too complicated. However, there are technical requirements that are higher than traditional stage lighting technology. That is: there are many computer lights involved in practical sound engineering, so engineering technology People should study hard in this regard. The engineers of Yihe Audio Company below will give you a brief explanation of how to debug some lighting equipment.
First of all, the individual operation status of each equipment should be carefully checked, because the control system and mechanical parts inside the computer light are relatively precise, the lighting power consumption is large, and the protection measures are relatively perfect, so if the internal control is caused by transportation or installation, If the component or the bulb is damaged, the computer light will not work normally. It is troublesome to confirm the fault of the faulty computer light in the complex lighting system. Therefore, it is necessary to check each unit separately before the system is connected or installed. The condition of the equipment can be done to check both the luminaire and the console.
Second, it is necessary to correctly set the lamps. It can be said that all the computer lights must work under the correct settings, so if the unit and system are in a normal and orderly state, the correct setting is very important. The settings include: the control form of the lamp, the power supply. The supply mode, the range of motion, the address of the luminaire in the system, and the processing of the control line terminal. Among them, the position setting of the luminaire in the system often causes errors in the project, and its setting is based on the selection of the address code. The DIP switch on the luminaire must be carried out in strict accordance with the form provided in the product manual, and can not be sloppy.
The other is the setting of the lighting control device. The biggest characteristic of computer lights is that they need to have corresponding settings and control devices to control the operation. If the console is improperly selected, the settings are unreasonable or faulty, the computer lights will not work properly or even work, especially complicated. The control system of the lighting system plays an important role in the normal operation of the light. Therefore, the equipment must be set. The setting contents include: control form, control signal output mode, model and quantity of the lamp, and control program software. Content and other aspects.
Finally, it needs to be explained: after the above steps are completed, it is necessary to check whether the action of the controller and the operation of the computer lamp are consistent with whether the self-test of the lamp is normal, etc., in addition, it is necessary to pay attention to whether the lighting system and the sound system interfere with each other. If yes, record the time of dry production and the model of the specific equipment to facilitate future resolution.
Special Textile/Braided Sleeve
easy to install, abrasion resistance, and shock proof properties, it`s widely used to irregular electric wire and hose for protection.
HNM -High Ware resisting Braided Sleeving is braided by specific high wear-resistant mono filament. High Ware resisting Braided Sleeve has the flexibility, flame retardancy and heat insulation properties like general PET braided sleeving, but its wear resistance is more than general PET three times.
KFL- Kevlar fiber braided sleeve is made of kevlar fiber with wear proof, humidity resistant, big tension, light-weight, stable dimension and other characteristics, Kevlar fiber braided sleeve can be used for protectiong the wire materials and rubber hose in bad evironments.
OAF- Aluminum Coated Fiberglass Heat Reflective Sleeve is made of two layers, the inner is weave by glass fiber yarn, foil glass fiber braided tube the outer layer coats a layer aluminum. Due to the use of special processing, the product good shading, reflecting heat, insulating heat, shielding signal, resistance to high-low temperature and other good characteristics.
Nomex braided sleeving is weave by pure nomex fiber braided sleeving. Nomex braided sleeve has strong mechanical toughness, flame retardant, anti-acid, anti-corrosion, light proportion. This sleeving can maintain its performance at extremely high temperature ( more than 245℃), moist or other extremely bad environment.
PNBT -Metal shield one side open dense weave protection braided tube , The AutoSCT2360 has excellent shielding, Open structure, Easy installation, Overhaul, And reusable. It is widely used for anti-interference shielding protection of electronic, electrical and mechanical, Railway,Automotive wiring harness,Fiber optic communication, And aerospace harness signals.
XWT- Basalt Fiber Braided Sleeving is braided by special basalt fiber yarn, high strength, high temperature resistance, oxidation resistance, radioresistance, heat and sound insulation, Good filterability, high compression strength, and high shear strength. Can be used in all kinds of environment. So it`s excellent insulation protection tube in extremely environment.
ZCK-Open Type Wave Grain Braided Sleeving is a new kind of braided sleeving, braided by polyester multifilament and acid lipid manofilament. It has characteristics good abrasion resistant, flame retardant, reducing noise, simple operation, ect. Open type structure is good to optical fiber wire harness for protection, reinstallation, maintenance and overhaul.
NLFZ- Flexible Non-shrink Nylon Textile Sleeving is weave by Nylon multifilament, it has smooth surface, strong stretching resistance, explosion proof and corrosion resistance, reducing noise and abrasion, moisture absorption and dustproof, and other good performance. It has better abrasion resistance and flexibility performance compared with dacron non shrinkable textile sleeving.
DXQZ- tin plated copper light weight shielding braided sleeving is made by specific copper wires which are braided refinedly, product has the advantages of shielding to electromagnetic signal, light weight, good flexibility and others, it can reduce the total weight of finished products compared with tin plated copper braided sleeves.
FZT - Noiseproof protection braided sleeving ,self-coiling shape weaved by polyester monofilament and multifilament, has the characteristics of good fireproofing, noise reduction, wear resistance, simple operation and others. Open structure is good for protecting wire harnesses, reinstalling, maintenance and servicing.
CFT-carbon fiber sleeve is braided by refined carbon fiber which is one kind of new materials with excellent mechanical properties. Its specific gravity is less than a quarter of steel. The tensile strength of the carbon fiber resin composite material is generally more than 3500Mpa. And is 7~9 times of steel. With super flexibility, resistance to high temperature, light proportion and other properties, it`s widely used in electric wires, cables and rubber tube which have irregular surface, and products have excellent stability and high torsional strength.
DXZPET tinned copper braided sleeve /tinned copper braided belt/copper braided wire
Product introduction:
Tinned copper braided sleeve/ tinned copper braided belt/ copper braided wire, is braided by multi-strand (example: 13s, 16s, 24s, 36s, 40s, 48s, 64s, 96s) high quality round copper wire or tinned soft round copper wire with the way of single layer or multilayer.
The outer diameter size of the copper wire: 0.1mm, 0.12mm, 0.15mm, 0.20mm.
The DC resistance ( 20℃ )of copper braided wire is not more than 0.22 Ωmm2 /m , the DC resistance ( 20℃ )of tinned copper braided wire is not more than 0.0234Ω mm2 /m .
Heat shrinkable braided sleeve,Carbon fiber braided sleeve,Kevlar fiber braided sleeve,foil glass fiber braided tube,Nomex braided sleeving,Basalt Fiber Braided Sleeving,tinned copper braided sleeve
KEYUACE Materials Co., Ltd. , https://www.insulationtubing.com