The configuration of LEDs in an application depends on a number of factors, including application requirements, LED parameters and quantities, input voltage, efficiency, thermal management, size and layout constraints, and optics. The simplest configuration is a single LE, and there are many applications with this design, such as car ceiling lights (map lights, reading lights).
Since the power and brightness of LEDs are not very high at present, and the actual use occasions usually require planar illumination, it is necessary to arrange multiple LEDs as needed to meet the requirements of larger range, higher brightness, dynamic display, color conversion, etc. Requirements and matching requirements between LEDs and associated drivers.
Common connection form
1, the overall serial form
(1) Simple tandem form
In the simple serial connection form, LED1~LEDn are connected end to end, and the current flowing through the LED is equal. For the same-size and batch LEDs, although the voltage on a single LED may have a slight difference, since the LEDs are current-type devices, it is possible to ensure that the respective luminous intensities are consistent, which is a simple series connection. The LED has the characteristics of simple circuit and convenient connection. However, due to the series connection, when one of the LEDs has an open circuit failure, the entire LED string will be extinguished, which affects the reliability of use.
(2) Series form with parallel Zener diodes
Each LED is connected in parallel with a modified series connection of Zener diodes. In this connection, the breakdown voltage of each Zener diode is higher than the operating voltage of the LED. When the LED is working normally, since the Zener diodes VD1~VDn are not conducting, the current mainly flows through the LED1~LEDn. When the LED string is damaged by the LED, the VD1~VDn is turned on, except In addition to the faulty LED, other LEDs still emit current through the current. This type of connection is greatly improved in reliability compared to a simple series.
Overall parallel form
(1) Simple parallel form
The LEDs 1~LEDn in the simple parallel form are connected in parallel at the beginning and the end, and each LED is subjected to the same voltage during operation. It can be seen from the characteristics of the LED that it is a current-type device, and a small change in the voltage applied to the LED will cause a large change in the current. In addition, due to the limitation of LED manufacturing technology, even the same batch of LEDs, the difference in performance is inherent, so when LED1~LEDn is working, the current of each LED is not equal. It can be seen that the insufficiency of the current distribution of each LED can cause the life of the LED with excessive current to be sharply reduced or even burned out. This connection is simpler. However, the reliability is not high, especially for applications where the number of LEDs is large, which is more likely to cause malfunctions.
(2) Independently matched parallel form
For the reliability problem existing in simple parallel, the independent matching parallel form is a good way. Each LED in this mode has its own current adjustability (driver V+ output is L1~Ln, respectively), ensuring that the current flowing through each LED is within its required range, with a good driving effect, a single LED When the protection is complete and the fault does not affect other LEDs, it can match the characteristics of LEDs with large differences. The main problem is that the structure of the whole driving circuit is complicated, the cost of the device is high, and the occupied volume is too large, which is not suitable for a large number of LED circuits.
Led Strip Connector is connected between the light bar, light bar is constantly presenting various lengths an accessory. Usually, by the light of the width divided into several types of connection fittings.
LED Strip Connector can be divided into waterproof and not waterproof, single and porous.
We focus on LED area, is a high-tech lighting enterprise deal in develop, produce and sales.
LED Strip Connector Owns DIP LED, SMD LED professional production lines and LED lighting products lines, the produce volume per month for DIP LED,SMD LED is 50 million pieces, for LED flexible strip light is 500 thousands meters, for LED flexible strip light for car is about 200 thousands pairs, for LED tube light is 50 thousands pieces, for LED Spotlights are 200 thousands pieces, for LED ceiling light are 50 thousands pieces.
Mingxue Optoelectronics Co.,Ltd. has apply the I S O 9 0 0 1: 2 0 0 8 international quality management system certificate, we apply the CE, RoHS and SAA certificate for our led lighting product as well as LED Strip Connector.
Our R & D team can handle highly customized designs and offer OEM and ODM services.
We hope to set up a long-term partnership with you through our high quality products and our Sincere Service!
LED Strip Connector
Led Strip Connector,8Mm Strip Connector,10Mm Strip Connector,Flexible Connector For Electrical Strip
Shenzhen Mingxue Optoelectronics CO.,Ltd , https://www.led-lamp-china.com