HQLL series material flow detection controller has strong structure and reliable performance
The HQLL-A type material flow detection device adopts a loading type test. After the tape in operation is loaded, the tape is lowered. The detection contact roller installed under the tape is pressed and the micro switch is actuated through the lever drive to output the switch signal. , to achieve the detection function. HQLL-B type material flow detection device adopts the detection method in which the hanging chain ball touches the material. When the tape conveys the material, the material pushes the ball and drives the swing arm to offset to one side. If the offset angle is greater than 20°, the internal switch operates. Output a set of switching signals. The working principle of the HQLL-C type material flow detection device is the same as that of the HQLL-B type.
HQLL series material flow detection controller has strong structure and reliable performance
HQLL series flow detection controller production site
HQLL series flow detection controller function
HQLL-01GHK/A Action angle: 20° Number of contacts: 1 Normally open 1 Normally closed contact Capacity: AC: 90-380V 15A IP65
HQLL-01GHK/B Operation angle: 20° Number of contacts: 1 Normally open 1 Normally closed contact Capacity: AC: 90-380V 15A IP65
HQLL-01GHK/C Operation angle: 20° Number of contacts: 1 Normally open 1 Normally closed contact Capacity: AC: 90-380V 15A IP65
HQLL series flow detection controller production site
HQLL series flow detection controller function
Environment and use of installation: This set of equipment is suitable for maintaining normal operation under the environment temperature -25 °C - +55 °C, relative humidity less than 85% of the environment. HQLL-A type is installed under the tape, and should be installed in the place where the amount of sinking is the largest. When it is no load, the tape and the contact wheel keep light contact. It is a product that is easy to promote. HQLL-B type and HQLL-C type are both The use of door bracket installation, suitable for wide belt, high speed conveyor. The test head is fixed on the cross beam, and the chain ball or the broom is in contact with the material. The height of the hammer or the broom can be determined according to the site conditions. The switch angle is 20° C. The angle of the tape dispenser can be adjusted properly. For single wall installations, refer to the door mounting method.
Because we are the most professional supplier of audio and video, our products include equipment, accessories, consumables, and our products.
The product is quality and safe!
We very much hope to establish long-term and stable cooperation with our customers.
We sell
All products are guaranteed quality!
We will provide customers with the use of each product.
To reduce
loss. If we discover the quality of our products, we will be responsible for the end
More professional consulting services!
The company's technical staff who are responsible for customer service are always available to provide you with
Preparation of maintenance, production process and product use and technology consulting
More favorable prices
Price is not the most important factor in determining purchase
Reliable, cost-effective
Is the most important
And we will make less profit than our peers and make more profit for our customers! Helping customers reduce
Production costs, increase production profits!
LCDS-1,
LCDS-2,
SDS-I,
SDS-1,
SDS-2,
XLDS-I,
QDS-II,
QDS-I,
XLDS-II,
LDM-G,
HLDM-KH-B,
HLDM-KH-A,
SFLC-I,
HQDM-1,
HQDM-2,
HQDM-I,
HQDM-II,
LDM-Y,
LLDS-I,
LLDS-II,
SFLC-I,
SFLC-II,
SDS-1,
YHLJ-II,
YHLJ-I,
CCS-1011,
SDS-2,
SDS-II,
XLDS-II,
JYB/LD-B,
SFLC-II,
KBD-X,
XYLC,
LCDS,
YWLC,
PCD,
LXM,
JB/T10936-2010
led grow light bar, horticulture lighting, quantum board driver, 1200W LED Driver, 720W led grow light
ShenZhen Fahold Electronic Limited , https://www.fahold.net